Airsoft Canada

Airsoft Canada (https://airsoftcanada.com/forums.php)
-   Doctor's Corner (https://airsoftcanada.com/forumdisplay.php?f=18)
-   -   WA 1911 slide getting stuck. (https://airsoftcanada.com/showthread.php?t=53064)

safx August 1st, 2008 20:59

My current project
 
Well I thought I would resurrect this thread
since the gun and mags finally ended up in
my hands, and I thought some might like to
know what was causing the problem.

Over the past day I've swapped out the metal
upgrades for stock plastic WA parts one by one
eventually getting the gun back to a stock state.
Usually metal upgrades need filing to work
properly, but not in this case.. I hope lol.

Now that the gun is all abs again, it's obvious
what's causing the issue— the nozzle. It's way
too loose in the breech. There's is roughly 2mm
of play upwards, which is leading to the nozzle
riding up on bbs and jamming it's self above the
loading ramp, and slightly deforming the loading
rubber, and letting the rear almost completely
leave the blow chamber. Ramming the slide
forward forces the nozzle's rear and o-ring to
scrape back into the breech/chamber, since they
are on an angle upward when stuck. The better
way is to release the mag, since it's holding up
the nozzle with follower or bb. The nozzle return
spring is also worn, weak and stretched a bit,
also contributing a bit to the issue.

Now I've gotta get a new nozzle or 2 to try out.
I don't know where the nozzle came from, or if
it's the original stock one for this gun but I'm
hoping a new SD complete nozzle with CP steel
return spring, and a new loading rubber, will fix
the jams once and for all. I'll update after the
new parts are installed.

Madmax, the WA's with springs on the inner barrel
to aid in returning the ejection port chamber to
battery are the SCW Hicap LE's and Experts. Not
much gained by them in my opinion.

safx September 1st, 2008 20:16

Update
 
Well after getting the gun working
with a new (full length) rear nozzle
cap the gun was shooting fine. So
I decided to strip the black spray
paint off the slide and swap some
parts to make 2 hybrids: A Para
HiCap and a SVI IED.

Unfortunately the Para slide was
nickel plated, I found out too late.
The paint stripper had ruined the
finish, so the long road of dremmel
sanding off the plate had begun.

Here's what's become of Brakoo's
old single stacker—

http://i210.photobucket.com/albums/b...c/IMG_2702.jpg
http://i210.photobucket.com/albums/b...c/IMG_2703.jpg
http://i210.photobucket.com/albums/b...c/IMG_2704.jpg
http://i210.photobucket.com/albums/b...c/IMG_2705.jpg
http://i210.photobucket.com/albums/b...c/IMG_2706.jpg
http://i210.photobucket.com/albums/b...c/IMG_2707.jpg

Brakoo September 6th, 2008 01:29

Good job and my bad about the paint, back then I went with the easy solution but I realized a little too late that my garage was too cold for the paint to adhere properly.

Dao September 7th, 2008 23:36

And now "part" of this badboy is coming to my collection :D

safx September 15th, 2008 11:53

Quote:

Originally Posted by Brakoo (Post 811286)
Good job and my bad about the paint, back then I went with the easy solution but I realized a little too late that my garage was too cold for the paint to adhere properly.

Thanks :)

Actually the paint job was pretty good. The
surface was slightly textured but really tough.

Discovered another issue with build— the
steel Guarder series 70 colt chamber was
meant for the SCW series. So it was also
helping cause the jams. I put that chamber
on another build with an SCW2 inner barrel
assembly and it was fine. The SCW ones
are cut a bit different.

I put a plastic black WA slide back on, with
a gold chamber and polished off the chrome
plate from the original barrel so it also looks
like gold lol, pimpin'! Pic to come later


All times are GMT -4. The time now is 13:59.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2025, vBulletin Solutions Inc.