P226 no longer fires.
 

After going through a clip, i have found that my KJW p226 no longer fires. After careful inspection I had found that the little notch that hits the valve release on the magazine has broken off. In other words its the little peice that hits the magazine to allow gas to pass through. Is there any way of replacing this piece? hopefully Any upgraded/TM parts?

You're looking for part P226-32 in the Marui manual. It may not fit the KJ P226 as the gun is not a 100% exact copy of Marui's.

Good luck finding that piece too :tup:

http://tech.airsoftcanada.com/TM/TM%...26diagram4.jpg

does it blow back but not return to the original slide position? my KJW P226 had that problem and in the KJW parts it's # 12 but the upgrade part that jugglez is talking about replaced mine as an exact match. if it's that problem then this may be the part

Jugglez nailed the right part. Anyone have any ideas as to where I can obtain this part?

hello sir downtown -one :) i have same problem i think that's item # 30 in our kjw P226 diagram it is the valve knocker , and i also followed ur thread entitled P226 double feeding= loading nozzle shredding, that's why i also replaced the recoil and loading muzzle to guarder,,,, and it also broke my valve knocker, and it seems i cant find a replacement, i went to a gunsmith, he told me he know's a guy who can fabricate a valve knocker made in steel,hopefully it works :)

downtown-one this is uptown-one, got a player returning via the upper path...

Sorry, nothing to contribute to the thread but saw the name and was glad to see another fan of that awesome flick! ;)

r2ditu, sounds like an idea. Let me know if it works out fine - if it does you think you can help me out too? I'd be willing to pay for it.

They carry P226-32 at Redwolf. Look under Parts-->TM GBB---> and there it is. I had to replace mine because the spring post broke after I upgraded the hammer spring (Guarder 150%, I don't recommend it). Hope that helps.

The Same thing happened to me, the knocker just suddenly broke on me. I've tried to take apart the rear chassis assembly but can't seem to get it out. Can anybody help me out here?

I really need help
 

Hi, I'm sorry for answering to this thread like this, but I really need help.

I'm not capable to re-assemble the valve knocker that I bought.

http://sbibuilder.free.fr/.tmp/p226/004.jpg

I only correctly (I think) have reassembled this parts.

How to re-assemble the whole ?

Thank you!!!

Is this a TM? From that angle im not sure at all, but there is only one correct place for all the parts, fun is following the guide and reasembling one at a time.. Just go slow untill you get it.

Thank for your answer, Renegade.

OK, first thing it isn't a TM but a KJ WORKS, but I checked both manuals and there were 100% similar.

In fact, I was looking for a solution since 1 month now. I never succeed and the result's: I can't re-assemble this alone.

The problem's that I can't understand the manual. It's looking very strange to me.

http://sbibuilder.free.fr/.tmp/p226/kjw_ok_small.jpg
(click to zoom in)

For example, the spring 31. How it can be here? 8O

And by the way, Sorry for my bad english.

Spring 31 keeps the tention on the valve knocker, meaning it holds it down but allows it to move up and down.

OK thanks for the info!!! But sorry I don't know how to place it in the valve knocker. Can you draw on the image where i should put this spring?

Thanks !!! :)

Well you see how it is shown to the left in the diagram? Thats how it goes on, just line it up, I think the bar of the spring goes on a small nich on top or just sits on top of the knocker, then the spring hole goes around the shaft obviously and put it back in the hammer assembly.