Airsoft Canada > Search Forums Search Results			User Name Remember Me? Password

Showing results 1 to 10 of 10 Search took 0.00 seconds. Search: Posts Made By: seanj

Forum: Newbie Tank December 24th, 2020, 02:52

Replies: 1,628 Sticky: Introduction Thread: Post your hello's here not somewhere else. Views: 3,590,600 Posted By seanj not a newbie to airsoft or the forum, but I did... not a newbie to airsoft or the forum, but I did just recover my account after roughly 4 years of inactivity, and looking forward to getting back at it!

Forum: Upgrades & Modifications November 4th, 2016, 01:08

Replies: 64 60+ rps build Views: 54,452 Posted By seanj What is Prz? What is Prz?

Forum: Upgrades & Modifications November 4th, 2016, 01:01

Replies: 64 60+ rps build Views: 54,452 Posted By seanj They (the fields) can, and should ban people who... They (the fields) can, and should ban people who regularly abuse the rules, and/or common sense. In paintball if you got a reputation for being a 'bonus baller' it was very hard to shake.

Forum: Upgrades & Modifications November 3rd, 2016, 20:02

Replies: 64 60+ rps build Views: 54,452 Posted By seanj This thread was entertaining. I'm going to... This thread was entertaining. I'm going to share a recent event relevant to the discussion on high fps at close range. I got shot in the arm point blank about a month and a half ago while...

Forum: Airsoft Guns Discussion May 16th, 2014, 18:27

Replies: 17 Question: KJW KP-07 MEU vs. Hi-Capa KP-05 vs. KP-08 Views: 18,887 Posted By seanj I'm not 100% sure about the new vs old co2... I'm not 100% sure about the new vs old co2 magazine thing, but the co2 mag that came with my KP-05 has a thick base plate and I purchased the pistol quite recently. I think about a month ago.

Forum: Airsoft Guns Discussion May 14th, 2014, 14:50

Replies: 17 Question: KJW KP-07 MEU vs. Hi-Capa KP-05 vs. KP-08 Views: 18,887 Posted By seanj I've got a KP-05 here are some measurements: ... I've got a KP-05 here are some measurements: grip width at trigger height (measured just below upper grip screw): 33.7 mm the grip width varies from around 33 mm to around 35.5 mm from top to...

Forum: Upgrades & Modifications April 21st, 2014, 01:29

Replies: 7 Lonex V2 Gearbox Compatible Recievers Views: 8,186 Posted By seanj I've got one sitting fairly nicely in a SRC m4a1,... I've got one sitting fairly nicely in a SRC m4a1, it required minor filing and sanding on the inside of the upper receiver to fit (i think because the cylinder installed in the gearbox is grooved on...

Forum: Newbie Tank March 18th, 2011, 20:28

Replies: 2 Question about hop up Views: 3,284 Posted By seanj are you 100% sure your hop up isn't simply... are you 100% sure your hop up isn't simply unwinding to zero hop? in my (semi-limited) experience when there's zero hop up the bb's usually seem to curve downwards unnaturally quickly somewhat like...

Forum: Newbie Tank March 12th, 2011, 23:39

Replies: 176 007 SRC Guns Views: 143,853 Posted By seanj I'm quite sure this is not true. I believe the... I'm quite sure this is not true. I believe the distinction is made based off kinetic energy not fps and as such a lighter plastic bb is subject to different limits then a heavier metal bb or pellet....

Forum: Airsoft Guns Discussion February 24th, 2011, 23:19

Replies: 18 SRC M4A1(GEN III) Vs . ICS-41 M4A1 Views: 15,199 Posted By seanj I feel it is a worthy use of my first post to say... I feel it is a worthy use of my first post to say I fully agree, I've been on many large forums and haven't seen anything like that behavior on any of them, its commendable.

Showing results 1 to 10 of 10