Airsoft Canada - View Single Post

t0aDe · June 13th, 2011, 14:41

Ok here's a troubleshooting puzzle for anyone who likes them, haha! I have
only started playing airsoft less than a month ago and have tried my best to
learn as much as I can but as you guys probably know there is A LOT to know.
I need enlightenment.

So a month-ish ago I purchased a used JG G36c with a triggermaster III
installed running on a 9.6v nimh. Currently fires about 350-360 fps on .2g
bb's. Out of the box the gun will not fire semi auto, no matter which position the fire selector is in the gun will be in the burst/hold for full auto mode. If I do a factory reset on the trigger master this is still the case. It even fires bursts for the first 5 trigger presses that are supposed to be "training" the computer for the mechbox, which I find odd. Basically it seems that the trigger master does not actually accept any instructions that I program (does not seem to change the fire modes when programming advanced options). Now what I suspect is that the fire selector in the mechbox is
dirty/not making proper contact, I'm hopefully pulling it apart this week to
find out and I'll let you know what I find... I was just wondering if anyone
else with a trigger master has had similar issues and if they know if its the
computer that is wonky or just that it is not taking input because the gun is
not set to semi as it should be for programming etc. It also seems to not
cycle the gearbox properly, but this I believe may be because I can't fire
the semi auto shots at "boot" like I need to. I try my best but often the gun
will start into a burst or I'll try to stop before it fires a second shot and
the box will cycle half way etc... :/

Now in addition to this issue (HAHA!) I recently bought a 11v lipo (gearbox is all shimmed up and such and obviously the gun is firing faster). The gun shoots fine (as in fires OK, the burst issue persists of course) but I've noticed
now that sometimes the nozzle at the end of the piston that moves back and
forth, letting bb's into the hop-up (forgive me not knowing what stuff is called) will rest in an open position (enough space for a bb to enter the
hopup) and will sort of dribble out of the gun after I fire a burst (a bb not the nozzle, lol). Any suggestions as to what I can do to remedy this? I've seen some people mention this can be caused by too weak a spring? I need to test again tonight when I get home but as far as I know this only happens when I use the 11v lipo.

Sorry if I'm missing any details I've tried to be as clear and meticulous as possible. Thanks in advance for whomever takes the time to ponder possible solutions!

June 13th, 2011, 14:41	#1
t0aDe Trader rating Join Date: Apr 2011 Location: Aurora, ON	Trigger master/mechbox/misc issue Ok here's a troubleshooting puzzle for anyone who likes them, haha! I have only started playing airsoft less than a month ago and have tried my best to learn as much as I can but as you guys probably know there is A LOT to know. I need enlightenment. So a month-ish ago I purchased a used JG G36c with a triggermaster III installed running on a 9.6v nimh. Currently fires about 350-360 fps on .2g bb's. Out of the box the gun will not fire semi auto, no matter which position the fire selector is in the gun will be in the burst/hold for full auto mode. If I do a factory reset on the trigger master this is still the case. It even fires bursts for the first 5 trigger presses that are supposed to be "training" the computer for the mechbox, which I find odd. Basically it seems that the trigger master does not actually accept any instructions that I program (does not seem to change the fire modes when programming advanced options). Now what I suspect is that the fire selector in the mechbox is dirty/not making proper contact, I'm hopefully pulling it apart this week to find out and I'll let you know what I find... I was just wondering if anyone else with a trigger master has had similar issues and if they know if its the computer that is wonky or just that it is not taking input because the gun is not set to semi as it should be for programming etc. It also seems to not cycle the gearbox properly, but this I believe may be because I can't fire the semi auto shots at "boot" like I need to. I try my best but often the gun will start into a burst or I'll try to stop before it fires a second shot and the box will cycle half way etc... :/ Now in addition to this issue (HAHA!) I recently bought a 11v lipo (gearbox is all shimmed up and such and obviously the gun is firing faster). The gun shoots fine (as in fires OK, the burst issue persists of course) but I've noticed now that sometimes the nozzle at the end of the piston that moves back and forth, letting bb's into the hop-up (forgive me not knowing what stuff is called) will rest in an open position (enough space for a bb to enter the hopup) and will sort of dribble out of the gun after I fire a burst (a bb not the nozzle, lol). Any suggestions as to what I can do to remedy this? I've seen some people mention this can be caused by too weak a spring? I need to test again tonight when I get home but as far as I know this only happens when I use the 11v lipo. Sorry if I'm missing any details I've tried to be as clear and meticulous as possible. Thanks in advance for whomever takes the time to ponder possible solutions!