JG G36C disassembly issue

jordanluong · April 28th, 2013, 04:33

Hey guys,

I was trying to disassemble my new JG G36C and when I came to the step where you remove the gearbox, I found these two wires instead of a tamiya connector. How would I go about removing these? Just pull? I've tried that but they seem very stuck together. Here is a picture of the two wires:

pestobanana · April 28th, 2013, 04:40

It looks like you need to unplug the battery and remove the hand guard

jordanluong · April 28th, 2013, 04:56

I've already done both of those, it seems that JG cheaped out and forgot to put a connector or something! What do you think?

pestobanana · April 28th, 2013, 05:51

Sorry I couldn't tell from the first photo. I've never seen a g36 wired like that in years and I sold my jg g36 6 years ago. Maybe just follow the wires and see where they go, they are most likely bound by plastic pull ties to the barrel leading to the fuse.

zone 69 · April 28th, 2013, 06:27

Quote:

Originally Posted by jordanluong

Hey guys,

I was trying to disassemble my new JG G36C and when I came to the step where you remove the gearbox, I found these two wires instead of a tamiya connector. How would I go about removing these? Just pull? I've tried that but they seem very stuck together. Here is a picture of the two wires:

It's hard to tell by the pic but are the two leads soldered together.?

If they are hit it with an iron and pull it apart at the same time.

MaciekA · April 28th, 2013, 06:41

Yank them apart. Connectors in this area are intended to allow you to separate your outer barrel and hop assembly.

For what it's worth, you should get rid of these connectors and the fuse, and switch to shortened Deans connectors.

jordanluong · April 29th, 2013, 02:36

Thanks for all the help!

I got past that and now I'm re-assembling my G36C but the barrel assembly does not want to fit into the upper receiver. I feel like pushing it any harder will damage it. It feels like its plastic against plastic and not wires getting caught. Any tips on helping getting the barrel assembly in so the bolts like up?

zone 69 · April 29th, 2013, 06:29

Don't the wire's feed here.?

BennyBoy · April 29th, 2013, 07:05

Maybe sure the hop up unit is not hitting anything?

pestobanana · April 29th, 2013, 15:23

Check how the hop up unit aligns with the nozzle. If the hop up unit meets up with the mechbox shell and that is what is causing the resistance, that is fine, the hop up unit has a spring to press tightly against the mechbox

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

April 28th, 2013, 04:33	#1
jordanluong Trader rating Join Date: Feb 2013 Location: Richmond Hill, ON	JG G36C disassembly issue Hey guys, I was trying to disassemble my new JG G36C and when I came to the step where you remove the gearbox, I found these two wires instead of a tamiya connector. How would I go about removing these? Just pull? I've tried that but they seem very stuck together. Here is a picture of the two wires:

April 28th, 2013, 06:41	#6
MaciekA Trader rating Join Date: Jun 2011 Location: Portland, Oregon, USA	Yank them apart. Connectors in this area are intended to allow you to separate your outer barrel and hop assembly. For what it's worth, you should get rid of these connectors and the fuse, and switch to shortened Deans connectors. __________________ "Mah check" Now you know

April 28th, 2013, 04:40	#2
pestobanana Squid Porn Superstar, I love the tentacles! Trader rating Join Date: Nov 2008 Location: Richmond Hill and Waterloo, Ontario	It looks like you need to unplug the battery and remove the hand guard

April 28th, 2013, 04:56	#3
jordanluong Trader rating Join Date: Feb 2013 Location: Richmond Hill, ON	I've already done both of those, it seems that JG cheaped out and forgot to put a connector or something! What do you think?

April 28th, 2013, 05:51	#4
pestobanana Squid Porn Superstar, I love the tentacles! Trader rating Join Date: Nov 2008 Location: Richmond Hill and Waterloo, Ontario	Sorry I couldn't tell from the first photo. I've never seen a g36 wired like that in years and I sold my jg g36 6 years ago. Maybe just follow the wires and see where they go, they are most likely bound by plastic pull ties to the barrel leading to the fuse.

April 29th, 2013, 02:36	#7
jordanluong Trader rating Join Date: Feb 2013 Location: Richmond Hill, ON	Thanks for all the help! I got past that and now I'm re-assembling my G36C but the barrel assembly does not want to fit into the upper receiver. I feel like pushing it any harder will damage it. It feels like its plastic against plastic and not wires getting caught. Any tips on helping getting the barrel assembly in so the bolts like up?

April 29th, 2013, 15:23	#10
pestobanana Squid Porn Superstar, I love the tentacles! Trader rating Join Date: Nov 2008 Location: Richmond Hill and Waterloo, Ontario	Check how the hop up unit aligns with the nozzle. If the hop up unit meets up with the mechbox shell and that is what is causing the resistance, that is fine, the hop up unit has a spring to press tightly against the mechbox

JG G36C disassembly issue

Doctor's Corner