so little velocity with such a setup??

sametwinnie · August 9th, 2015, 18:46

Hi everyone, I bought a used King Arms M4 and decided to upgrade it.
The problems is I’m having only 233fps (constant) with this setup….
I never chrono the gun before the upgrade but I don’t know why it chrono like this.
The gearbox is shimmed the right way.

This is my set-up:

WiiTech Air-tight Nozzle, M4 Series

Hotpower 11.1V, 15C Lipo

JingGong Silver Wire Assembly With MOSFET

FMA "NOVESKE"+ -14mm Silencer (4'', CW, CCW)

Modify Professional 2-Ring+ Hop Up Bucking for Modify Hybrid Inn

Modify Hybrid 6.03mm Precision Inner Barrel 407 mm

Wii Tech M110 Spring

Lonex A2 TITAN Orange Infinite Torque-Up Motor

Lonex Enhanced Super Gear Set - High Speed Ratio (16:1)

Lonex Extreme Toughness Piston (10-Teeth - Burgundy)

Lonex POM Ventilated Piston Head

Lonex Aluminum Cylinder Head for Ver. 2

Dean everywhere

I must say that I put Mobil bearing grease inside the gearbox which I know it's not ideal.

Any idea how to diagnose this problem??

Thanks

GR · August 9th, 2015, 23:06

Sounds like compression issues. Check the hop up (teflon tape if your friend), as well as the piston (open up the gearbox, take away the spring, push the piston all the way to the cylinder head, cover the nozzle with a finger, then try to pull out the piston).

Hectic · August 10th, 2015, 01:20

You'll actually want to install the nozzle ant tappet and hold them I the forward position then try to put the piston forward to check for compression.
but yes sounds like air leak. What cylinder are you using, where is the port located?
And yes could be a hop up leak someplace as well.

Wrath144 · August 10th, 2015, 02:38

Try this: https://www.youtube.com/watch?v=v1i5rCMiueE

thetuch · August 23rd, 2015, 04:15

Be sure to check the seal between your air nozzle and hop up unit as well. Sometimes the specs between brands are different and can result in poor seals. If you have another hop up unit try it out. You can lose a surprising amount of air pressure between those two points.

cetane · August 23rd, 2015, 14:26

What cylinder do you have? And if it's ported, is the port towards the rear of the gearbox where they should be?

Home	Forums	Register	Gallery	FAQ	Calendar
Retailers	Community	News/Info	International Retailers	IRC	Today's Posts

British Columbia	Alberta
BCAC	EAR
Op-For	JOC
Northern Arms Airsoft	Skunkworx Airsoft
Airsoft Kelowna	RAAT
Prince George Airsoft	Manitoba
Saskatchewan	MAA
SK Airsoft	Ontario
PDW	Airsoft Ottawa
South Sask Mercs	Snow Dragons
Quebec	1st Ranger Platoon
PQAC	Wolfpack Tactical
1st Pathfinders Regiment	TTAC3
Quebec Airsoft
MTX Airsoft	Atlantic
FAQc	Atlantic Airsoft

August 9th, 2015, 18:46	#1
sametwinnie Trader rating Join Date: Jul 2006 Location: quebec	so little velocity with such a setup?? Hi everyone, I bought a used King Arms M4 and decided to upgrade it. The problems is I’m having only 233fps (constant) with this setup…. I never chrono the gun before the upgrade but I don’t know why it chrono like this. The gearbox is shimmed the right way. This is my set-up: WiiTech Air-tight Nozzle, M4 Series Hotpower 11.1V, 15C Lipo JingGong Silver Wire Assembly With MOSFET FMA "NOVESKE"+ -14mm Silencer (4'', CW, CCW) Modify Professional 2-Ring+ Hop Up Bucking for Modify Hybrid Inn Modify Hybrid 6.03mm Precision Inner Barrel 407 mm Wii Tech M110 Spring Lonex A2 TITAN Orange Infinite Torque-Up Motor Lonex Enhanced Super Gear Set - High Speed Ratio (16:1) Lonex Extreme Toughness Piston (10-Teeth - Burgundy) Lonex POM Ventilated Piston Head Lonex Aluminum Cylinder Head for Ver. 2 Dean everywhere I must say that I put Mobil bearing grease inside the gearbox which I know it's not ideal. Any idea how to diagnose this problem?? Thanks

August 10th, 2015, 02:38	#4
Wrath144 formerly steyr Trader rating Join Date: Sep 2005 Location: Winnipeg, Manitoba	Try this: https://www.youtube.com/watch?v=v1i5rCMiueE __________________ BROFORCE Admin - Winnipeg Airsoft

August 9th, 2015, 23:06	#2
GR Trader rating Join Date: Jun 2014 Location: Somewhere in Ontario...	Sounds like compression issues. Check the hop up (teflon tape if your friend), as well as the piston (open up the gearbox, take away the spring, push the piston all the way to the cylinder head, cover the nozzle with a finger, then try to pull out the piston).

August 23rd, 2015, 04:15	#5
thetuch Trader rating Join Date: May 2011 Location: Vancouver	Be sure to check the seal between your air nozzle and hop up unit as well. Sometimes the specs between brands are different and can result in poor seals. If you have another hop up unit try it out. You can lose a surprising amount of air pressure between those two points.

August 23rd, 2015, 14:26	#6
cetane Trader rating Join Date: Jun 2010 Location: Markham & Stouffville - Ontario - Canada	What cylinder do you have? And if it's ported, is the port towards the rear of the gearbox where they should be?

so little velocity with such a setup??

Upgrades & Modifications